XTA DS8000D Featuring all new microphone pre-amps designed by Gottelier award winning Alex Cooper, the DS8000 offers many new facilities including a dual redundant power supply*, simple Outside Broadcast â€œone to manyâ€ split switching and 48V â€œsafeâ€œ functions to prevent tampering. Subtle panel lighting for dark under-stage environments and the option of adding an ADC card for integration into digital networks, plus bespoke new output transformers all combine to produce a package that enhances its predecessorâ€™s reputation as a flexible, rugged high quality distribution system. Rugged 2U steel casing with recessed control panel area to avoid damage and accidental adjustments. Subtle illumination of control panel area for low light conditions. DC power supply link capability â€“ enables safe fail over mode for paired units in the event of a power loss to either unit. New design discrete mic preamps with exceptional noise and CMR for incredible performance, even with long cables (typically 120dB at 1kHz). Improved gain range now switchable in 6dB steps from -6dB up to +42dB. Individual channel 4 segment LED metering with attendant solo and 48V indicators. Remote control of phantom power on inputs via sensing on FOH and MON outputs. Individual phantom power on all channels, with â€œsafeâ€ switching for FOH, MON and front panel. Ground lift circuit switches to prevent hum â€“ separate MON and FOH control. â€œO/B Splitâ€ modes switchable to feed channel 1â€™s input to first 16 outputs, or channel 5â€™s to last 16 outputs. Add even more flexibility with 2 x 8 AES outputs, with wordclock sync and master clock out. Featuring reassuring XTA quality ADCs operating at 48, 96 or 192k, this is all available in addtiion to the already comprehensive analogue output makeup. Solo listen with high power phones amp and external bus to allow other units to be monitored without having to move headphones jack. DS8000D â€“ go digital Add even more flexibility with 2 x 8 AES outputs, with wordclock sync and master clock out. Featuring reassuring XTA quality ADCs operating at 48, 96 or 192k, this is all available in addtiion to the already comprehensive analogue output makeup. Inputs Electronic Max input level: +26dBu Differential Impedance 10k 100Hz CMRR @0dB gain 85dB typ. 100Hz CMRR @30dB gain 120dB typ. 1kHz CMRR @0dB gain 85dB typ. 1kHz CMRR @30dB gain 120dB typ. Inputs Transformer Isolated As above except: Max broad spectrum level: +26dBu Max LF level: +16dBu (30Hz) Differential Impedance 5k Isolation 2.5kV Outputs Electronic Max output level: +20dBu (600R) Diff. Impedance less than 50ohms Outputs Transformer Isolated Max output level: +10dBu (600R) Nominal level: -10dB Diff. Impedance less than 150ohms Isolation 2.5kV System Freq. Response 22-22k +0/-0.5dB XFMR Option Freq. Response 22-22k +0/-1.5dB EIN (0dB gain, 22-22k) less than -101dBu EIN (30dB gain, 22-22k) less than -124dBu Power 90-240VAC, nominal less than 30W Weight (no options) less than 6kg The audio distribution system shall be of an active design providing 8 independent channels in a standard 2 unit, 19â€³ rackmount enclosure. Each channel shall provide two outputs that are actively balanced, and accessible via rear panel XLR connectors, and two that are transformer isolated and accessible via front panel XLR connectors. The input shall accommodate line level signals of up to +26dBu without clipping. Each channel shall provide switched gain adjustment in 9 steps via a front panel control, 48V phantom power shall be selectable via a front panel switch, 4 segment LED metering and â€˜Soloâ€™ facility via a front panel switch. Phantom power shall be remotely enabled when 48V power is detected on the â€˜Monâ€™ or â€˜FOHâ€™ XLR connectors on the rear panel.The device shall include a headphone â€˜Soloâ€™ facility via a 1 / 4 inch phone connector with associated level control. Remote phantom power and front panel phantom power switching may be disabled via rear panel â€˜Safeâ€™ switches. Ground lift switches shall disconnect the internal ground connection in two banks (inputs 1-4, 5-8). An â€˜OB Splitâ€™ function shall feed input 1 to outputs 1-4 or input 5 to outputs 5-8 via two rear panel switches with front panel indication. The unit shall have the option to have AES digital outputs fitted in addition to the standard analogue outputs. The device shall provide facility to link the â€˜Listenâ€™ busses together when using multiple devices. The device shall be powered from an internal power supply, which will operate from an 90-240V 50/60Hz power supply. A single unit shall be capable of providing power to another connected unit via a 5 pin XLR power link cable, and this switchover shall be automatic with front panel indcation of the power supply state. The audio distribution system shall be the XTA Electronics DS8000.
Be the first to review this product.
- 30.00 KGS